Perlick Refrigerator BSDZ User Manual

INSTALLATION ANd OPERATION INSTRUCTIONS  
dUAL ZONE bACk bAR CAbINET — SELf CONTAINEd  
MOdEL NOS.  
BSDZ Series  
bSdZ60  
IMPORTANT INfORMATION  
Table of Contents  
to register your product, visit our web site at  
PreParing the Cabinet  
(www.perlick.com). Click on “Commercial”, then  
“Service”. You will see the link to “Warranty  
registration Form”. You must complete and submit  
this form or the installation date will revert back to  
the ship Date.  
Specifications........................................................2  
tools required.......................................................3  
Plumbing ...............................................................3  
electrical................................................................3  
Uncrating and inspection......................................3  
installing Casters or Legs ....................................3  
Placing the Cabinet...............................................3  
Leveling the Cabinet .............................................3  
installing the base Plate........................................3  
refrigeration and temperature Control.................4  
Cleaning the Cabinet.............................................4  
Cleaning the Condenser .......................................4  
Cleaning Stainless Steel........................................4  
replacement Parts................................................5  
reversing Door hinge ...........................................6  
Wiring Diagram......................................................7  
This manual has been prepared to assist you in the  
installation of your Cabinet and to acquaint you  
with its operation and maintenance.  
We dedicate considerable time to ensure that our  
products provide the highest level of customer  
satisfaction. If service is required, your dealer can  
provide you with a list of qualified service agents.  
For your own protection, never return merchandise  
for credit without our approval.  
We thank you for selecting a Perlick product and  
assure you of our continuing interest in your  
satisfaction.  
WARNING: When lifting, the full weight of the  
cabinet must be supported. Lift from the cabinet  
base and not from the top. Improper lifting can  
result in severe damage to the cabinet.  
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069  
Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com  
Form no. Z2304  
rev. 05.22.10  
 
Preparing the Cabinet for Use  
Suggested Tools  
Installing base Plate (Optional)  
#2 Phillips Screwdriver.  
attach brackets to cabinet bottom in holes pro-  
vided. attach base plate to brackets. (See separate  
instructions, provided with kit). When returning  
cabinet to upright position, be careful not to bend  
brackets.  
10” Crescent Wrench.  
9/16” allen Wrench.  
5/16and 3/8” hex Socket.  
Power Drill or Driver.  
WARNING!  
Plumbing  
To avoid compressor damage, after returning  
cabinet to an upright position, let unit stand for  
24 hours before plugging it in.  
no plumbing required. Condensate from the cooling  
coil is automatically evaporated through a condensate  
pan located in the side condensing unit compartment.  
For your convenience, a factory installed floor drain  
is located in the back right corner of the cabinet. this  
can be plumbed to an external floor drain. the floor  
drain can be plumbed from the cabinet right side  
using a 34” nPt connection or out the bottom using  
a 1” nPS connection. both ports of the drain come  
capped from the factory.  
Placing the Cabinet  
Push the cabinet into place using rollers when  
necessary. Important: Proper air flow around the  
condensing unit is necessary for efficient operation.  
never obstruct the air flow in and out of the  
condensing unit.  
For sanitation purposes, it may be necessary to  
seal the base of the cabinet to the floor. this can be  
accomplished by laying a bead of silicone sealant  
between the base of the cabinet and the floor as  
shown by the figure at below.  
Electrical  
the cabinet must be connected to a separately  
fused power source (see electrical specification  
plate) and grounded in accordance with national  
and Local electrical Codes. Caution: Do not  
attempt to operate the equipment on any other  
power source than that listed on the electrical  
Specification plate.  
CABINET  
BEAD SILICON  
SEALER (RTV)  
Uncrating and Inspection  
remove all crating material before operating.  
Carefully inspect cabinet for hidden damage. if  
damage is discovered, file your claim immediately  
with the transportation company. Perlick is  
not responsible for damage in transit.  
FLOOR  
Leveling the Cabinet  
When the cabinet is in place, check installation with  
carpenter’s level. When level front to back and left  
to right, accumulated water will drain out of cabinet  
evaporator drain.  
Installing Casters or Legs (Optional)  
attach four casters or legs to the cabinet bottom;  
mount rigid casters at the rear and swivel casters on  
the front. Use the supplied 1/4”- 20 x 3/4hex head  
self-tapping machine screws.  
Perlick is committed to continuous improvement. therefore, we reserve the right to change specifications without prior notice.  
Form no. Z2304  
rev. 05.22.10  
3
 
general information  
NOTE:  
Refrigeration and Temperature Control  
Cabinet temperatures lower than 34° will not allow  
for proper defrosting of the evaporator coil. if  
defrosting is necessary, remove product from the  
cabinet and turn the control adjusting screw to the  
OFF position until coil is defrosted.  
each zone has been factory set to maintain the  
desired temperature specified when ordered. the  
factory set storage temperatures are as follows:  
refrigerator — 34° to 38° F  
White wine — 50° to 55° F  
red wine — 60° to 65° F  
Cleaning the Cabinet  
Use a mild detergent and water to clean the inside  
and outside of the cabinet. Dry thoroughly. never  
use a scouring pad or abrasive cleanser.  
NOTE: an industrial strength, commercial cleaner  
can be used to clean the outside of painted  
cabinets.  
Adjusting the Temperature  
the temperature control in the left compartment is  
located on the left side of the evaporator fan panel.  
the temperature control in the right compartment is  
located on the top rear partition wall. You will need  
a flat head screwdriver to turn the adjusting screw  
on the control. make small adjustments until the  
desired temperature is achieved.  
Cleaning the Condenser  
the condenser (located behind the front grille  
cover) should be inspected every 30 days and  
cleaned, if necessary.  
Colder Temperatures:  
turn the adjusting screw clockwise (to the right).  
Warmer Temperatures:  
Use a long handled, stiff brush to clean the dirt  
from the front surface of the condenser. Keeping  
the condenser free from dust and dirt will ensure  
efficient operation.  
turn the adjusting screw counterclockwise  
(to the left).  
Temperature Control “Off”:  
turn the adjusting screw completely counter-  
clockwise to the “O” position until a click is  
noted.  
Failure to keep the condenser clean will cause a  
loss in condensing unit efficiency, and may damage  
the compressor.  
the condenser fan motor turns off and on with  
the compressor. the evaporator fan motor runs  
continuously. the partition wall fan cycles with  
the damper assembly.  
CAUTION: Do not bend the fins while brushing the  
front of the condenser.  
Recommended Cleaning Agents  
JOb  
CLEANING AGENT*  
COMMENTS  
routine Cleaning  
Soap, ammonia, detergent  
apply with sponge or cloth.  
Can be used on all finishes.  
Fingerprints and smears  
areal 20, Lac-O-nu, Lumin Wash,  
Provides barrier film to minimize  
O’Cedar Cream Polish  
fingerprints. Can be used on all finishes.  
Stubborn stains and  
Discolorations  
allchem Concentrated Cleaner,  
Samae, twinkle, Zud restoro,  
rub lightly, using dry or damp  
cloth in the direction of polish  
lines on the stainless steel.  
grade F or FFF italian Pumice,  
Whiting or talc, Liquid nu Steel,  
Copper’s or revere Stainless Steel  
Cleaner, Lumin Cleaner, Sta-Clean,  
Cameo Copper Cleaner, allen Polish  
highlite, Penny-brite, Copper brite  
* Use of propriety names is intended only to indicate a type of cleaner and does not constitute an endorsement.Omission of  
any proprietary cleaner does not imply its inadequacy. All products should be used in strict accordance with instructions on  
the package. nOte: Do not Use Steel Wool or Scouring Pads to clean stainless steel.  
Perlick is committed to continuous improvement. therefore, we reserve the right to change specifications without prior notice.  
Form no. Z2304  
rev. 05.22.10  
4
 
Replacement Parts – Dual Zone Back Bar Cabinets  
MODEL NOS.  
Complete condensing unit  
Replacement compressor, R134a  
Condensing unit fan motor assembly  
Condenser Coil  
BSDZ60  
C22647  
513200314UA.2  
515315009  
15352019  
519100088  
US-PB10HBX1  
US-PB10HBX1  
US-PB10HBX1  
57699  
Terminal board  
Overload protector  
Relay  
Start capacitor  
Fan blade, evaporator  
Fan motor, evaporator  
Fan motor, partition wall  
Fan guard, partition wall  
Fan guard, evaporator  
Temperature control, refrigerator  
Temperature control, wine  
Solenoid, damper  
C15239A  
65253  
65254  
65557  
61283  
C12827W  
65778  
Damper blade, assembly  
Evaporator coil  
65783  
66572  
Liquid and suction line assembly  
Pan, evaporator  
65084  
66579-1  
Wire harness, compressor bottom  
Wire harness, evaporator  
Wire harness, partition wall (damper)  
Wire harness, light jumper  
Wire harness, mullion heater  
Light bulb  
65560  
65561  
65776  
65538  
65571  
63821  
Light bulb guard  
65525  
Light socket  
63484  
Light switch  
65535  
Lock  
63762  
Space, lock  
63761-1  
Lock rail  
65432-24SS or 65432-24  
65432-1-12SS or 65432-12  
66210-12SS or 66210-12  
65565-1  
Grille, rail  
Grille, front  
Condensate pan  
Panel, end, condensor unit housing  
Panel, rear, condensor unit housing  
Door sill  
66215-1SS  
65435-12SS  
65500-1  
Door handle full length SS  
Gasket, door  
65305-1  
66237-4  
Hinge group, right  
Hinge group, left  
66264R  
66264L  
Hinge pin  
63679-1  
Shelf, wire  
62307-2  
Shelf, wine rack  
66413  
Clip, shelf  
C15875  
*Replacement top  
*Replacement door  
RT-NL2  
RD-NL2  
*Contact Perlick Milwaukee for complete door and top replacement. Cabinet serial no. required.  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2304  
Rev. 05.22.10  
5
 
reversing Door hinge  
STEP 8:  
Tools Required  
re-assemble hinge brackets to unit. bottom right brack-  
et is assembled as the top left bracket. top right bracket  
is assembled as the bottom left bracket.  
#3 Phillips Screwdriver.  
1/16” allen Wrench.  
Flathead Screwdriver  
STEP 9:  
re-insert top hinge pin.  
Right Hinged door  
(as shipped from factory)  
STEP 10:  
re-assemble lock rail from  
Handle Styles  
Bottom Hinge Bracket Top Hinge Bracket  
SteP #3  
Operations to Perform on door  
Step #14  
65305-1  
C31409-1  
STEP 11:  
Not  
Reversible  
remove bottom  
door hinge bracket  
from door assem-  
bly and remove  
65189  
65609-2  
door hinge bushing  
from bracket.  
re-assemble door  
hinge bracket to  
previous position,  
without bushing.  
Operations to Perform on Cabinet  
STEP 1:  
remove bottom hinge pin from  
assembly.  
STEP 2:  
STEP 12:  
Carefully lift and tilt out door  
assembly from the unit and  
set aside.  
remove top door  
hinge bracket from  
door assembly and  
Step #12  
Step #11  
Step #13  
assemble door  
hinge bushing from  
SteP 11 to bracket. re-assemble door hinge bracket to  
previous position with bushing attached.  
STEP 3:  
remove lock rail from  
cabinet, requires removal of  
four screws.  
STEP 13:  
door with full length SS handle:  
there is no need to remove door handle. it will be  
positioned correctly when door is reversed.  
STEP 4:  
Remove  
these screws  
remove top hinge pin.  
remove top and bottom  
hinge brackets from the unit.  
door with SS pull tab or handle with wrap-  
around bracket:  
STEP 5:  
remove hinge bushing from  
bottom hinge bracket and  
remove the two screws mounting the handle and  
reposition to appropriate location on the opposite  
side of the door.  
Top Hinge Bracket Bottom Hinge Bracket  
assemble to top hinge bracket.  
STEP 14:  
STEP 6:  
remove lock retainer and install on opposite end of  
Hinge Bushing  
taking care not to scratch the  
surface, remove hole plugs  
from the left hinge holes.  
door.  
STEP 15:  
What was the door top is now the door bottom.  
Carefully lift the door onto the hinge brackets of the  
cabinet. the two hinge bushings should meet. reinsert  
the bottom hinge pin to complete the door switching  
operation.  
Step #7  
STEP 7:  
insert hole plugs into vacant right  
hinge holes.  
Step #6  
Perlick is committed to continuous improvement. therefore, we reserve the right to change specifications without prior notice.  
Form no. Z2304  
rev. 05.22.10  
6
 
Wiring Diagram – bSDZ60 2 Door Dual Zone back bar Cabinet  
[2] DOOR  
MULLION HEATER  
RED  
LIGHT  
SWITCH  
BLACK  
WHITE  
WHITE  
WHITE  
BLACK  
LIGHT  
LIGHT  
SOLENOID  
(Partition Wall)  
THERMOSTAT  
(Partition Wall)  
EVAPORATOR FAN  
BLACK  
WHITE  
BLACK  
BLACK  
WHITE  
WHITE  
FAN MOTOR  
(Partition Wall)  
BLACK  
THERMOSTAT  
(Compartment #1)  
POWER CONNECTION  
CONDENSING UNIT  
BLACK  
WHITE  
GREEN  
JUNCTION BOX  
Perlick is committed to continuous improvement. therefore, we reserve the right to change specifications without prior notice.  
Form no. Z2304  
rev. 05.22.10  
7
 
8300 West good hope road • milwaukee, Wi 53223 • Phone 414-353-7060 • Fax 414-353-7069  
toll Free 800-558-5592 • e-mail: Perlick@Perlick.com • www.Perlick.com  
Perlick is committed to continuous improvement. therefore, we reserve the right to change specifications without prior notice.  
Form no. Z2304  
rev. 05.22.10  
8
 

Peavey Musical Instrument Amplifier 410TVX User Manual
Peavey Speaker System SP 4Ti User Manual
Peripheral Electronics Furnace PGHGM3 User Manual
Philips CRT Television 15PT166A 00 User Manual
Philips DVD Player DVD622 User Manual
Philips Range 32PFL7332D User Manual
Philips Work Light 5791231 16 User Manual
Pioneer DVD Player DV 868AVi User Manual
Procom Indoor Fireplace V50TYLA BC User Manual
ProForm Treadmill 831295230 User Manual